|
 |
Description |
Emerald-MM-8Plus is a high performance multi-protocol serial communications board offering eight ports on a single PC/104-Plus module. Supporting baud rates up to 921.6K bps in RS-232 mode or 1.8432Mbps in RS422 or RS485 mode, each port can be individually selected for RS-232, RS-422, RS-485 or TTL level operation. Both local-echo and non-local-echo modes are supported for RS-485. Protocol selection is achieved via a jumper block for each of the eight ports. Line termination for RS-422/485 modes is also jumper-selectable.
Configuration of the Emerald-MM-8Plus is simple, using the built-in plug and play technology. For manual configuration, the base address for the board may be set in software, defining a 4K block of configuration space used to access the on-board registers. A single 32-bit read shows the detailed interrupt status for each of the eight ports. The PCI slot is defined through a jumper block. As with all Diamond Systems products, jumpers are paralleled with locations for zero ohm resistors to create a rugged, shock-and- vibration-resistant implementation.
Emerald-MM-8Plus is based on the Exar 17D158 octal UART IC. This device contains 8 4 identical sets of 16C55registers, one for each port, and is compatible with the standard PC serial port. Each port contains 64-byte transmit and receive FIFOs to support the high-speed data rates.
Emerald-MM-8Plus also offers 8 convenient digital I/O lines. The direction of each line is independently programmable. Finally, Emerald-MM-8Plus also offers a 16-bit programmable counter / timer with a configurable clock source.
Two I/O headers are provided, with four serial ports and four digital I/O lines on each header. The board operates on +5V only, eliminating the need for a +12V supply that is often required for serial port operation.
|
Operating Systems Compatibility |
The Emerald-MM-8Plus uses the Exar (Maxlinear) XR17D158 UART which is based on the industry-standard 16C550 UART. Drivers are available for most popular embedded operating systems. Check the drivers included with your OS or the Support tab for drivers on this producdt page, or else visit maxlinear.com.
|
Cables |
EMM-8Plus-XT uses 2 of Diamond's C-DB9M-4 cable for the 8 serial ports. Each cable has a 2x20 .1" pitch socket header to connect to the board's pin header and 4 DB9 Male panel-mountable connectors for user connections.
| Cable |
Description |
Drawing |
| C-DB9M-4 |
Quad DB9 male to 40-pin header 18" cable, Serial ports 1-4 (uses 2) |
Show |
|
Specifications |
| Serial Ports |
| Number of serial ports |
8 |
| Protocols |
RS-232, RS-422, RS-485 (local and no echo) |
| Protocol Configuration |
Jumpers |
| Software Configuration |
Plug and Play |
| Maximum baud rate |
1.8432Mbps |
| Communications parameters |
5, 6, 7, or 8 data bits; Even, odd, or no parity |
| Short circuit protection |
Continuous, all outputs |
| RS-232 mode |
| Input Impedance |
3KΩ min |
| Input voltage swing |
30V maximum |
| Output voltage swing |
5V min, 7V typical |
| RS-422/RS-485 modes: |
| Differential input threshold |
-0.2V min, +0.2V max |
| Input impedance |
12KΩ minimum |
| Input current |
+1.0mA max (Vin = 12V)
-0.8mA max (Vin = -7V) |
| Differential output voltage |
2.0V min (RL=50Ω) |
High/low states differentia
output voltage symmetry |
0.2V max |
| Digital I/O |
| Number of I/O lines |
8 individually programmable |
| Input voltage |
Logic 0: -0.3V min, 0.8V max
Logic 1: 2.0V min, 5.3V max |
| Output voltage |
0: 6mA max
1: -4mA max |
| General |
| I/O header |
2 40-position (2x20) .025" square pin header on .1" centers;
Headers mate with standard ribbon cable (IDC) connectors |
| Dimensions |
3.55" x 3.775" |
| Power supply |
+5VDC 10% |
| Current consumption |
160mA typical, all outputs unloaded |
| Operating temperature |
-40°C to +85°C standard, all versions |
| Weight |
3.1oz (87.9g) |
| RoHS |
Compliant |
|
